TP321H and TP347H (UNS S32109 / S34709) are the high-carbon versions of the titanium- and niobium-stabilised austenitics. The carbon range of 0.04–0.10% is the whole point: standard 321 and 347 are capped at 0.08% and are intended for corrosion resistance, while the H grades are intended for creep strength at 600 °C and above in furnace and boiler tubing.

Both grades exist to solve the same problem: chromium carbide precipitation at 450–850 °C in the weld heat-affected zone, which leaves the steel vulnerable to intergranular corrosion. Titanium in 321H and niobium in 347H combine with carbon preferentially, keeping chromium in solution. The stabilising ratio is specified — Ti at 4 × carbon minimum for 321H, Nb at 8 × carbon minimum for 347H.
The difference between the two is temperature. 347H holds creep strength to about 650 °C and is the default for refinery furnace tubes and reformer pigtails; 321H is used to roughly 600 °C and in boiler superheater service where its lower cost matters. Above 650 °C both give way to 800H or a centrifugal casting.
Neither grade tolerates chloride well — stress corrosion cracking in wet chlorides is the standard failure mode, and insulation lagging that traps water is the usual trigger. They are also not resistant to polythionic acid attack after shutdown if the stabilising ratio is at the low end, which is why the ratio is checked on the certificate rather than assumed.
Standards and Equivalent Grades
A213 covers seamless tube; A312 covers pipe; A249 and A269 cover welded tube. The H designation must be explicit on the order — a mill supplying 321 instead of 321H will meet the chemistry table at a glance but miss the carbon minimum, and the difference only shows up in a creep test.
| System | TP321H | TP347H |
| UNS | S32109 | S34709 |
| W.Nr. | 1.4878 | 1.4912 |
| ASTM A213 | Seamless tube | Seamless tube |
| ASTM A312 | Seamless and welded pipe | Seamless and welded pipe |
| GB | 07Cr18Ni11Ti | 07Cr18Ni11Nb |
Where These Tubes Are Used
Refinery furnace tubes
Convection and radiant sections of crude and vacuum heaters, where 347H resists polythionic acid attack during shutdown.
Boiler superheaters and reheaters
Superheater pendants and outlet sections at 580–620 °C steam temperature.
HRSG modules
Superheater and reheater tube bundles in combined-cycle plants, welded to headers of matching grade.
Reformer pigtails
Outlet pigtails and transfer lines on hydrogen reformers, where thermal fatigue governs.
Ethylene convection section
Convection coils upstream of the cracking furnace, where 347H bridges the transition to 800H.
Heat exchanger tubing
High-temperature process exchangers where carbon steel or 316L would scale or creep.
Supply Range and Condition
Seamless tube from 6 mm to 219 mm outside diameter, wall 1.0 mm to 25 mm; U-bent tube to drawing with bend radius from 1.5 D. Standard condition is solution annealed at 1,050–1,150 °C and pickled, with bright annealing available for instrument and small-bore sizes.
Testing includes hydrostatic or eddy current test, flattening and flare tests, intergranular corrosion test to ASTM A262 Practice E where specified, and grain size to ASTM E112 (grain size 7 or coarser is usual for creep service). EN 10204 3.1 certificates with heat traceability.
Chemical Composition (wt%)
The stabilising element ratio is the acceptance criterion that matters. A 321H heat at 0.08% carbon needs at least 0.32% titanium; a 347H heat at the same carbon needs 0.64% niobium. Certificate values below those ratios pass the elemental ranges but fail the intent of the grade.
| Element | TP321H | TP347H |
| Carbon (C) | 0.04–0.10 | 0.04–0.10 |
| Chromium (Cr) | 17.0–19.0 | 17.0–19.0 |
| Nickel (Ni) | 9.0–12.0 | 9.0–13.0 |
| Titanium (Ti) | 4 × C min, 0.60 max | — |
| Niobium + Ta | — | 8 × C min, 1.00 max |
| Manganese (Mn) | 2.00 max | 2.00 max |
| Silicon (Si) | 1.00 max | 1.00 max |
| Phosphorus (P) | 0.045 max | 0.045 max |
| Sulphur (S) | 0.030 max | 0.030 max |
Mechanical Properties
Values are the ASTM A213 minima at room temperature. Creep rupture strength, not tensile strength, is what qualifies these grades for service — the H designation is what makes the 100,000-hour data applicable.
| Property (room temperature) | TP321H / TP347H |
| Tensile strength | ≥ 515 MPa |
| Yield strength (0.2%) | ≥ 205 MPa |
| Elongation in 50 mm | ≥ 30% |
| Hardness | ≤ 90 HRB |
Need TP321H or TP347H seamless tube to A213?
Send the outside diameter, wall, length, quantity and the stabilising ratio or grain size requirement — we reply with mill availability, lead time and a priced offer, usually within one working day.