TWZ-4 is TISCO’s molybdenum-nickel non-magnetic grade: 965 MPa minimum yield in HS temper, 1.7–2.5% molybdenum and 3.0–4.5% nickel for pitting resistance in heavy sections, relative permeability 1.005 max, to works specification Q/TX 085-2019.

TWZ-4 non magnetic drill collar for MWD and LWD
TWZ-4 in HS temper, 965 MPa min. yield
GradeTWZ-4 (PNM650)
MillTISCO
Yield strength965 MPa HS

TWZ-4 is the molybdenum-nickel member of the TISCO non-magnetic family. It is not stronger than TWZ-3 in HS temper — both are guaranteed at 965 MPa — it is more corrosion resistant: 1.7 to 2.5 percent molybdenum and 3.0 to 4.5 percent nickel hold pitting resistance in heavy sections and in chloride-rich mud where the leaner grades run out of margin.

Grade and specification

Item TWZ-4
Mill TISCO (Taiyuan Iron & Steel)
Works specification Q/TX 085-2019
Type Austenitic Mn-Cr-Mo-Ni-N, low carbon
Product forms Forged bar, rolled bar, hollow bar, collar blanks
Temper HS (cold worked) or LS (solution annealed)

The designation is the mill’s. It is what appears on the mill test certificate and on the shipping documents — we do not re-badge grades.

Applications

Non-magnetic drill collars and BHA components in wells where pitting, not load, sets the service life.

  • Heavy-section collars where cold reduction is limited by the bar size
  • Wells with high chloride mud or elevated bottom-hole temperature
  • MWD and LWD housings that must hold permeability through machining
  • Stabiliser mandrels and non-magnetic subs in corrosive service
  • Replacement for nickel-based alloys where an austenitic Mn-Cr-Mo-N grade will do the duty

Sizes and delivery

Form Range
Forged / rolled round bar OD 80 – 300 mm
Hollow bar and collar blanks OD 90 – 280 mm, bore to drawing
Cut-to-length Any length up to 6 m
HS temper Guaranteed up to OD 280 mm, banded
Custom melt 3 – 5 t minimum for a fresh induction melt

Chemical composition

Heat analysis, mass percent, to Q/TX 085-2019.

Element TWZ-4 Element TWZ-4
C max. 0.04 Cr 18.00 – 19.00
Si max. 1.00 Mo 1.70 – 2.50
Mn 20.00 – 23.50 Ni 3.00 – 4.50
P max. 0.025 N 0.55 – 0.70
S max. 0.010 Nb, Ti, V trace additions permitted

Full limits are printed on the mill certificate; a specimen certificate is available before you order.

Mechanical properties

Minimum values at room temperature, by outside-diameter band.

Property HS temper, OD ≤ 235 mm HS temper, OD 235–280 mm LS temper, OD 80–450 mm
Yield strength Re, min. 965 MPa 900 MPa 900 MPa
Tensile strength Rm, min. 1035 MPa 1035 MPa 1035 MPa
Elongation A, min. 20% 20% 20%
Impact KV, min. 100 J 100 J 100 J
Hardness 330–430 HBW, surface 330–430 HBW, surface 330–430 HBW, surface

Relative permeability ≤ 1.005 and magnetic field gradient ≤ 0.05 µT per 100 mm, verified on every collar by probe testing and supplied as a printout with the certificate. 1 ksi = 6.895 MPa.

Melting and processing

  • Melting: EAF + AOD, LF refining, then ingot or vertical casting; ESR on request
  • Hot working: forged or rolled with a reduction ratio of 6 or better
  • Heat treatment: solution anneal and water quench; warm forging followed by quenching to prevent sensitisation
  • Finishing: peeled, turned, BTA bored, gun-drilled, thread and shoulder to drawing

Inspection and certification

  • Chemical analysis and mechanical testing per heat to ASTM A370
  • ASTM A262 Practice A and E for intergranular attack
  • ASTM G36 / G38 C-ring stress-corrosion testing on request
  • Full-length ultrasonic inspection to API Spec 7-1 clause 12
  • Probe testing of permeability on every bar, printout supplied
  • EN 10204 3.1 certificate as standard, 3.2 and SGS / TÜV on request

Need TWZ-4 non magnetic collar bars?

Send the outside diameter, bore, length, temper and quantity, plus any sour-service or permeability requirement — we reply with mill availability, certificate scope and a priced offer, usually within one working day.

Request a quotationWhatsApp