15-15HS Max is Carpenter’s nitrogen-strengthened chromium-manganese austenitic, developed for one job: carrying load in a drill string without disturbing a magnetic survey. Warm-worked bar reaches 1,145 MPa yield at 3.5 inch section while magnetic permeability stays below 1.01 — roughly twice the yield of Nitronic 50 at the same non-magnetic behaviour.

15-15HS Max non-magnetic stainless steel bar for drill collars and MWD housings
Yield ≥ 966 MPa (140 ksi); permeability < 1.01.
Grade familyCr-Mn-N austenitic
Yield strength≥ 966 MPa (140 ksi)
Permeability< 1.01
PRE> 30

The chemistry is 18% manganese, 19% chromium and up to 0.70% nitrogen — no nickel to speak of, because nickel is what makes conventional stainless magnetic in the wrong way and expensive in the right way. Strength comes from nitrogen in solid solution plus warm working, not from a heat treatment, so there is no quench distortion to machine out afterwards.

The lower carbon content (0.04% maximum) compared with earlier chrome-manganese grades is the ‘Max’ part: less chromium carbide at the grain boundaries means better resistance to intergranular stress corrosion cracking, which is the failure mode that shortens drill collar life in chloride-bearing muds. Typical PRE is above 30.

In service the alloy is used as-forged or warm-worked. Annealing at 1,040–1,150 °C and water quenching restores ductility at a large strength cost (490 MPa yield), so it is only done when a part has to be re-formed. For drill collars, a post-machining internal-diameter compressive stress treatment is specified to further improve stress corrosion resistance.

Grade Identification and Product Forms

15-15HS Max is a proprietary Carpenter grade without a UNS number; enquiries usually cite the trade name. Permeability is verified to ASTM A342. Bars are supplied as rounds, hollow bar and multi-dimensional (shaped) bar — the last form is used where a drill collar or stabiliser body is machined from near-net stock.

Data on this page are the published Carpenter typical values (datasheet edition 8/1/12). They are typical, not minimums, and should be confirmed against the mill certificate for the specific heat and section.

Item Detail
Trade name CarTech 15-15HS Max
Family Austenitic Cr-Mn-N stainless
Forms Bar rounds, hollow bar, multi-dimensional bar
Permeability test ASTM A342, 1.002 at 200 oersteds
Typical PRE > 30

Where 15-15HS Max Is Used

Non-magnetic drill collars

The main application: collar bodies and slick sections that must not deflect the compass in a magnetic survey.

Stabilisers and near-bit tools

Blade and sleeve bodies where strength and non-magnetic behaviour are both required.

MWD and LWD housings

Instrument carriers with thin walls and high load paths.

Jars and shock subs

Components that see impact loading in a non-magnetic assembly.

Logging tool bodies

Sonde housings for wireline tools run in cased or open hole.

Hang-off and master subs

Load-bearing subs at the top of a non-magnetic BHA section.

Supply Range and Condition

Rounds at 88.9 mm (3.5 in), 127.0 mm (5.0 in) and 177.8 mm (7.0 in) are the standard sections for which published properties exist; larger sections and hollow bar are quoted on enquiry. Standard condition is as-forged or warm-worked — the strength in the tables depends on that, so the condition must be stated on the order.

Annealing, if required, is 1,040–1,150 °C with one hour per inch of thickness and a water quench. Welding is possible with standard electric-arc methods, but matching-composition consumables are not commercially available, so joints are normally mechanical.

Chemical Composition of 15-15HS Max (nominal, wt%)

Carpenter publishes a single nominal figure for each element rather than a range; the entries marked ‘up to’ are maxima. Manganese at 18% and chromium at 19% are what the ’15-15′ name refers to in the original grade; nitrogen up to 0.70% is the strengthening element and the reason the alloy needs no ageing treatment.

Element Nominal
Carbon (C) 0.04 max
Manganese (Mn) 18.00
Phosphorus (P) 0.050 max
Sulphur (S) 0.050 max
Silicon (Si) 0.50
Chromium (Cr) 19.00
Nickel (Ni) 3.50 max
Molybdenum (Mo) 3.00 max
Nitrogen (N) 0.70 max
Iron (Fe) balance

Mechanical and Magnetic Properties

Values are typical room-temperature properties published by Carpenter for warm-worked bar, showing how yield falls as section size increases. The annealed row is included for comparison only — it is not a service condition for drill collars.

Permeability is below 1.01 on the Severn gauge and 1.002 by ASTM A342 at 200 oersteds, in both the annealed and warm-worked conditions.

Bar size Yield (0.2%) Tensile Elongation Charpy V Hardness
88.9 mm (3.5 in) 1,145 MPa (166 ksi) 1,289 MPa (187 ksi) 21% 199 J (147 ft-lb) C37
127.0 mm (5.0 in) 1,082 MPa (157 ksi) 1,213 MPa (176 ksi) 22% 194 J (143 ft-lb) C38
177.8 mm (7.0 in) 1,062 MPa (154 ksi) 1,193 MPa (173 ksi) 23% 178 J (131 ft-lb) C38
Condition Yield Tensile Elongation Reduction of area Hardness
Annealed 1,065 °C, WQ 490 MPa (71 ksi) 828 MPa (120 ksi) 56% 79% B95

Need 15-15HS Max non-magnetic bar for drill collars or MWD housings?

Send the diameter, length, condition and the required yield or permeability — we reply with mill availability, lead time and a priced offer, usually within one working day.

Request a quotationWhatsApp +86 178 7358 1838